How do you clean your beads?

Started by sparrow, February 15, 2009, 06:55:23 AM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

sparrow

I know this has been discussed before, but with a couple of tool tips jumping up recently, and quite a few newbies around, I thought it might be worth another topic?

Also, because.........am I the only one who cleans without any motorised implement, and am I being stupid to do so? Do you guys use your Dremels etc. under water? I just can't imagine cleaning beads without water to dampen the nasty dust, but similarly, I just can't bring myself to take an electric tool to a water source?

Just call me newbie ;)
Sabine x

www.littlecastledesigns.co.uk www.facebook.com/littlecastledesigns Ring Top Tutorial

Dee Dee

Quote from: sparrow on February 15, 2009, 06:55:23 AM
Also, because.........am I the only one who cleans without any motorised implement, and am I being stupid to do so?


No, you're not the only one - I don't have a flex-shaft thingy and wouldn't be happy putting my dremel end in water, I can be such a butter fingers!

So I use a bead reamer.

Steph x

Kaz

Re-chargeable Dremel so you are not attached to the power source when using. I put the beads in a washing up bowl with warm water and a smidge of washing up liquid. Then I have a jug of hot water beside me. I don't clean the beads under the water (I find it too slippy and hard to locate the hole) but the beads (and release) are wet and I then dip the diamond bit into the jug of water and put all the cleaned beads into the jug. I then wash them in hot soapy water and put them in a sieve and run clean water over them. I have been known to put them through the dishwasher once bead release has been removed.
Kazx
She's made of real glass. She got real real emotion. But my heart laughs I have that same sweet devotion!

turnedlight

I just use a diamond reamer - I don't usually have heaps of beads to clean though, when I have had a real pile of them I've wondered if there's a better way! I don't find it too much of a drag. Oh and I don't batch anneal.. maybe if I was doing that I'd be using something else. :)
kathryn

Shirley

I clean mine by hand too. Tend to do it while I'm watching (or half watching) tv. Bought a fancy dremel and decided it was a silly waste of money so took it back and got a refund. I think I'm less likely to chip the beads doing it by hand.
Val Cox Frit - Thai and Bali Silver 

Fabienne

I do the same as Kaz, saves loads of time! Love my cordless Dremel would not be without it.
Fabienne
x

sparrow

Glad I asked the question....I often only have 20 beads or so (from an 'after work' session), but every now and then, it'll be 100 in one go (including spacers). Maybe I ought to implement the 'in front of telly' strategy. I'm like you Shirley, scared of chipping, but presumably that's just because I can't use the tool properly, as I know the people who clean their beads with a dremel wouldn't sell on chipped beadies either, so....hmmmm......Hardest thing is keeping Toby patient while I clean - it usually costs me one grape per bead ;)
Sabine x

www.littlecastledesigns.co.uk www.facebook.com/littlecastledesigns Ring Top Tutorial

Sarah

You could try a flexshaft on your dremel so that the motor is a long way away from the water. The trick to avoid chipping is to use a very slow speed and to put the bit in the hole before you switch it on and to switch it off before you take it out.

I use my proxxon if I have a lot of beads; otherwise I do them by hand with a mandrel and some polishing compound Becky gave me.

Sarah
xxx

sparrow

Thanks Sarah - somebody was selling a flexshaft on here a while ago, but I was too slow.....will keep pondering. The cordless idea sounds nice too  :)
Sabine x

www.littlecastledesigns.co.uk www.facebook.com/littlecastledesigns Ring Top Tutorial

Lush!

Y'all know I often have half a ton of beads to clean at once  ;)

My routine is similar to Kaz's - except my beads get more a cold shower than a hot bubble bath!  I don't put my dremel-type-thingy in the water but my beads are wet and I dip them back in the water or under the tap when I finish reaming.

And I agree with Sarah - only turn the drill on when its in the hole to avoid chipping.

Okay Newbie?   ;D ;D


www.lushlampwork.etsy.com

Sarah

Quote from: sparrow on February 15, 2009, 09:32:24 AM
Thanks Sarah - somebody was selling a flexshaft on here a while ago, but I was too slow.....will keep pondering.

My fingers were very quick on that one Sabine  ;) I'd been after one for a while  :)

dinah46

Flexshaft on a dremel under the trickling cold tap to protect the diamond coating on the beadreamer which is fab

Big hole beads just get started with a tile saw blade and finished off with a hand reamer, again under trickling cold water.

I got my flexshaft with the dremel and use it a lot, it's a lot easier to hold than the large body of the dremel - I only have ickle hands ???

Trudi

Quote from: Lush! on February 15, 2009, 09:36:46 AM
Y'all know I often have half a ton of beads to clean at once  ;)

My routine is similar to Kaz's - except my beads get more a cold shower than a hot bubble bath!  I don't put my dremel-type-thingy in the water but my beads are wet and I dip them back in the water or under the tap when I finish reaming.


Snap!

And rather then just using my chunky house drill, I've just bought a rotary tool from Focus half price £12.49. And somepne just posted a thread saying that Aldi are getting some in next week I beleive for about £11.

T

saffie

dremel same as Kaz but no flexi shaft. i keep the beads in water clean them out of the water but dip the bead in and out to rinse it. also occasionally dip the diamond tip thingy in the water but v. carefully

sparrow

Quote from: Sarah on February 15, 2009, 09:48:27 AM
Quote from: sparrow on February 15, 2009, 09:32:24 AM
Thanks Sarah - somebody was selling a flexshaft on here a while ago, but I was too slow.....will keep pondering.

My fingers were very quick on that one Sabine  ;) I'd been after one for a while  :)


AAaaah, 'twas you  ;D ;D ;D ;D Okay, I think my dremel might move back inside......hmmmmmm.........it's good to be a newbie now and then ;)
Sabine x

www.littlecastledesigns.co.uk www.facebook.com/littlecastledesigns Ring Top Tutorial