Is my oxycon dying?!?

Started by princess pink, December 28, 2010, 10:49:34 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

princess pink

Ok had bill the oxycon since June 09 and he's been chugging along fine. Cold weather hits and he didn't like it and beeped at me a lot thought it just needed to warm up til I torched again. Today was a balmy 7 degrees, considerably warmer than last week abd after 5 mins the orange light is on and it beeps inanely at me. Red light came on last week but not today. When I switch it off abd on again it does the same within 5 mins.

Things I've tried: turned oxy down to 2 lpm while it warms up, then up to 3.5lpm for normal use and same problems. Tend to work on low flow anyway. Also tried checking the outer filter and lifted off the flap on top but nothing seemed awry. I also tried lifting it a couple inches off ground and dropping it. Still nothing to stop it beeping.

Heeeeeeeeelllllppppppp!!!!!


ScarletLeonard

Oh No!!!

Bring him into a nice warm room and let him have a cosy night near a radiator? he may just still be to cold. then try him on a plug socket in the house and see if he behaves?

7 degrees? you lucky thing best we have had is 1.5

Redhotsal

Open him up and check all his tubing. The change in weather may have made a tube crack. If you have a leak inside he won't work properly, possibly, not at all. If you see an obvious leak see if you can repair it and try and get hold of some silicon tubing to replace it.

princess pink

Ok when you say open him up, how exactly do I do that?

Redhotsal

Depends on whether he's a modern one or an old one, but they all open up like a book. There should be a seam running down the middle from top to bottom and a long hinge opposite this. Mine are all the "old style" so I haven't opened up a newer version, so I don't know exactly where the screws will be on yours but you should look for two large screws which hold it all together, there will be one at the top and one at the bottom. Have a look at where the black filter/air intake is - you should see a screw there and then flip him upsidedown and there should be a screw at the bottom - usually in a recess so it's hard to spot. Just unscrew these and prise the two halves apart.

When he's open don't be surprised if lots of black gunk falls out. Depending on how old the unit is the innner foam which soundproofs the compressor may/may not be starting to fall apart. It's probably best to move all the loose bits and give it all a general clean out. You might also want to check that the fan is seated properly (this is what dropping the unit from a few inches is meant to do - but as you can imagine it can also unseat the fan more instead of making the connection better). The fan is a push in unit and if it's not pushed into it's connector securely it won't work and the unit will red light.

Once you've made sure the fan is okay just have a good look - you'll see lots of yellowy tubing. If the unit is old this will be quite yellow and brittle. It will crack easily and once you have a crack or a leak in this hosing there will be an internal oxygen leak and the unit won't function. You might want to get hold of some new tubing (check out aquatic supply shops or Google silicon tubing) and replace. You can do a temporary repair by taping up a leak if you see one but it will be much better to replace all the tubing sooner or later as once the stuff starts going brittle it leaks from all sorts of places. You can attach the tubing with plastic cable ties but make sure the internal diameter (ID) of the new pipe matches your existing pipe.

You can also remove the internal air filters for more efficient running. If you look inside the unit there are "flying saucer" shaped white objects inline with the tubing. These are there for filtering biological nasties out - you don't need them for lampworking as you are not breathing the O2 directly so if you take them out the chances are that the unit will run better - and you won't need so much tubing.

There may be other factors which are preventing the unit from working but generally the above usually fixes about 80% of my oxycon problems.

princess pink

wow! thanks sal! appreciate the advice. will attack bill next week and see what happens!

Barbara

Let your oxycon work one day on low flow in a warm and dry room. Perhaps he pulled wetness, and with this long run it can be possible to dry him.