finally set up...HELP!

Started by Esmé, December 05, 2010, 08:51:25 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Esmé

Hello everyone!  ;D

Well I have finally got my studio set up (yes I spend hours just sitting in it, im a saddo!)  I've been out and bought my propane, my boyfriend kindly attached the pipes between the hothead and propane tank (got the bulk setup from tuffnells) but now we're a bit stuck.  How far open do we need the regulator (and is that up or down?)  How much should we open the valve on the hothead itself?  We tried lighting it yesterday, after a few attempts it lit but the blue flame was much smaller than I expected, is this because I'm using propane and not Mapp?

Oooh, I'm absolutely itching to get started but am completely terrified!  Was anyone else nervous?  Someone hold my hand!

★★Terri★★

1. Screw the regulator right down - then just turn the knob back a little bit. 
2. Turn the gas right up (on the tank) and just turn the gas knob on the torch on. 
3. There is very little, if any, control on the hot head itself.  Sometimes if the torch is cold it helps to block the holes a bit when lighting it.  Make a narrow band with tin foil and wrap it around the holes (I use my hand to hold it - it's not hot at this point but you may want to use oven gloves or something similar). 
4. I use one of those clicky gas BBQ lighters (cheap ones from pound land etc) and hold the lighter flame just on the edge of the hot head nozzle.  Lighter flame going - turn on the knob on the hot head.  It will be bushy/yellow flame to start with. 
5. Slowly release the foil from the holes and the flame will start to be straighter and bluer. 

You may find you need to do this a couple of times to start with.

Magpie

Quote from: Esmé on December 05, 2010, 08:51:25 AM
Oooh, I'm absolutely itching to get started but am completely terrified!  Was anyone else nervous?  Someone hold my hand!

Yes! I was petrified the first time I lit up on my own. Don't worry it passes quite quickly. And everyone on here will be holding your hand, virtually at least. ;D

Have fun.

Esmé

well thank you for the advise!  I've just made my first bead!!!! I'm so excited! I'm going to burst.......My name's Esmé and I'm a bead-a-holic!

★★Terri★★


ScarletLeonard

Quote from: Terri on December 05, 2010, 09:05:11 AM
2. Turn the gas right up (on the tank) and just turn the gas knob on the torch on. 

I don't turn the gas bottle full on - there's no need because the regulator won't let any more through than it's set for.
I turn my HH about halfway, light turn down slightly then slowly turn up. Any other way and the flame just goes out.

Glad you got it sorted and you've made your first bead. I couldn't help but grin like a Cheshire cat as I made my first and laughing as all I could say to myself was "ohh look your doing it"

Have fun and remember piccies.

AnnaSpanna

I do two "natural" turns on the propane tank to open it - so prob just over 360 degrees. My regulator is prob a full turn open from closed. My HH tap gets opened 180 degrees and that seems to work well for me. I agree that sometimes after my torch has been sitting for a while unused then it can be difficult to light so the tinfoil over the holes for a few seconds after lighting does the trick. I always bleed the pipes once I finish for the day (turn off propane tank and when the flame naturally goes out on the HH then turn that off too).

Enjoy your beading!

helenfc


Margram

Wahey - well done! I was terrified when I started ;D If you do use a barbeque lighter (and I do), remember to put it well out of the way after you light up. Close the flashback regulator (by turning it anti-clockwise) before opening the propane on the tank and then turn it clockwise to open up. This apparantly prolongs the life of the regulator.
Marg x  Etsy Flickr My blog

sarah t

i was told that you turn the valve fully on so should you need to turn it off in a hurry it will only go one way ...off...

and i dont fiddle with the regulator either ...but different strokes for different folks what ever makes you happy  ;D

well done and have fun  ;D ;D ;D

Esmé

Thanks again everyone for the help.  I was sooooo scared!

I spent a couple of hours (on and off) at the torch yesterday, and had a go at putting bubbles in things, adding frit, ooooh loads of pretty colour experiments!  I'm so happy!  Gonna post a pic of my first beads in a minute when I find where to put them!