Frit-Happens !

Technical Forum => Studio/workspace/setup/equipment => Oxycon/Oxygen/Propane => Topic started by: Lush! on November 04, 2011, 06:49:09 PM

Title: Devilbiss Mini MC44 oxycon connection
Post by: Lush! on November 04, 2011, 06:49:09 PM
Does anybody else have one of these oxycons?

I've been fiddling with the bluddy thing for the past hour and a half and just noticed a Tuffnells sticker on it so could have asked them for help - too late now though.

It doesn't take the usual green cone shaped screw connector so whenever I move it (trying to get an extra torch set up for teaching tomorrow) I really struggle to get a seal.

I've padded the hose with a bit of cut off hosing and am trying to tighten it onto the connector - just a short narrow pipe that sticks out from the oxycon at a right angle - with a jubilee clip or even cable ties.  I have lemon crimps but no tool to tighten them.

IF I can get a lemon-crimp-tightening-tool (name, anybody?  ???) from B&Q in the morning, will it work?

Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: helbels on November 04, 2011, 06:56:49 PM
Julie, I just tightened my lemon clip with a huge pair of bog standard pliers.  It was hard, but if you squeeze like billyo, it's possible.
Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: MangoBeads on November 04, 2011, 10:42:04 PM
Julie i dont think you will get the lemon clip pliers at b and q so that may be a wasted trip. But good pliers should do it if you have the lemon clips . Hope the weekend goes well :) xxx
Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: MangoBeads on November 04, 2011, 10:49:47 PM
david says get electricians electrical tape wind it round the nozzle put the end of pipe in hot water and wedge over electrical tape bulge and then use a jubilee clip . You can make up any size with electrical tape :)
Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: julieHB on November 04, 2011, 10:52:02 PM
Quote from: MangoBeads on November 04, 2011, 10:49:47 PM
david says get electricians electrical tape wind it round the nozzle put the end of pipe in hot water and wedge over electrical tape bulge and then use a jubilee clip . You can make up any size with electrical tape :)

That's what I did too - there's no point in using the lemon clips, a jubilee clip is ample.  Grrr, I hated those connections!!!
Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: Lush! on November 05, 2011, 12:31:07 AM
David to the rescue again! I don't know how I'd manage without all these other halves looking after me  ;D ;D
Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: firedinglass on November 05, 2011, 05:43:23 AM
Yep, that's what i used, a plain old jubilee clip  ( no idea what a lemon crimp is!)
Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: HelenV on November 05, 2011, 01:23:37 PM
Mine's on just with a jubilee clip - I needed the hot water to stretch it on - and now I can`t get it off :-)

Hope you get it sorted xx

(http://i280.photobucket.com/albums/kk188/vanek_03/IMG_8707.jpg)
Title: Re: Devilbiss Mini MC44 oxycon connection
Post by: MangoBeads on November 05, 2011, 01:26:51 PM
Quote from: Lush! on November 05, 2011, 12:31:07 AM
David to the rescue again! I don't know how I'd manage without all these other halves looking after me  ;D ;D

:) I heard a whisper that there are plans a foot for a few other halfs to come your :) way shall I add David to the list !!!! he comes with half a dog :) :) :)