Nope, I haven't gone nuts, just wondering what people use to get the inside of their kilns shiny clean.
Our house one is massive and I just don't think I can be bothered to keep lugging it around to use (at all, never mind for the kiln... ;)) and I was on the lookout for a handheld jobbie instead. So riddle me this - does it need to have hepa filtration (cos of all the teeny tiny bits) or is 'five stage filtration' enough???
Am I the only one whose made their mum's year back in 199? by helping dad choose them a dust buster for mothers day? No? Just me???
Ah well.
Lucas
i have got a bead cube so i just tip it forward and use a paint brush :o
When it was at home I used the normal house one, which just has normal filtration, now at the studio I use the Henry, no idea do they even have filtration systems?
And yes, I remember when dust busters were all the rage
I've got a cheapish bagless cylinder type which comes apart to fit in a box out of the way. Is meaty enough to clean a house, bought one for DH before he was DH and needed a new vac but small enough for the shedios. Think I got from Argos or somewhere equally easy to access, perhaps Sainsbury's? It does everything for me from velvet fluff in the big shedio to dust and bits in the small shedio. Good for doing the car as well, as small enough to get in the boot without having to kill my back. Was a recognised make but if that is viutally important to anyone let me know and I'll venture into the cold to find out for you.
I have a little portable one, it's mains powered but came out a second hand shop, it looks really, really old. I've not used the normal vacuum on it as the kiln I have is fibre lined and it doesn't take much for the fibre to loosen and come out it little clumps. >:(
QuoteAnd yes, I remember when dust busters were all the rage
I used to work with a guy who stared in the advert whith his sister when he was a kid!
I got one with Tiger Tokens from the Esso garage (circa 1989?). My mum has a Morphy Richards one, albeit a newer model.HTH. :)
I use a Henry for my kiln, the house one really isnt suitable.
I use a hake brush and it goes as follows.
Forget to clean the kiln for many many months
Realise I need to clean the kiln when it coughs every time I open the bead door.
Open the lid to clean it, realise I don't have the hoover to hand so use a hake brush.
Brush entire contents out of the kiln door onto glass and tools underneath
Spend the next week having to clean EVERY tool and piece of glass that I use.
Give in, clear off the whole work table, hoover it all up and curse myself for not hoovering out the kiln in the first place ::)
I use a bagless cheapy thing from Tesco, it lives in the studio so no conamination with anything else. I have the extraction on and a mask when I hoover any of the kilns out.
Just did Big Blue as I relined him in preparation for big hare!
:-[ I just lay a dampened piece of kitchen towel on the SC3 kiln floor (when I remember) and sort of edge the 'droppings' out...I am in a shed though, right by the door, so practically outdoors.
See, I thought hubby was being over cautious! I'm just gonna buy something handy then, that has a stretchy cord or something so I can get it inside...
Thanks guys!
;D ;D ;D
Lucas
Vacuum my kiln?? I don't even vacuum my house if I can help it! After all, what are children for??!! ;D
I just use an old stencil brush to take out any bits of release but there's usually very little so it only gets done every few weeks.
That's fine Pat for a front loader, top loading kilns though get a bit heavy to tip on their side to do it this way! ;D
I have a little cilinder type one that cost about£20 from currys or comet or PC world.
The kiln is by the door so always have it open when I hoover it out,which i do every firing and I use fiber paper.
I'm just surprised that there is a need to frequently hoover out the kiln. My big old ceramics kiln, albeit a front loader too,(internal measurements w. 30cm h. 30 cm depth 30 cm) very rarely needed hoovering even though I used both fiber paper and batwash depending on the project. I always lifted out the shelves keeping them horizontal before tipping into a black sack while holding on to the shelf. Dust and debris was trapped in the sack. The kiln has exposed heating elements on both sides and the floor and a dedicated 30 amp main.Keeping shelves horizontal was a knack I had to PPP because small pieces before fusing had a habit of moving when I walked from the lounge to the garage, (through two doors and down a back step) ;D ;D ;D
I can't honestly say I hoover mine out lots Pat, although I do think some of it depends on whether you use thinfire or batt wash predominantly. I find thinfire creates quite a bit of dust.
Also, with a top loader, especially a fire brick one (like my Hot Start, as opposed to ceramic fibre, like my new Bill) does tend to create dust and 'crumbs' - the action of opening and closing the lid cannot help but create a bit of extra dust - with a front loader, I'd expect most of that to simply fall on the floor in front of the kiln when you open the door.
And, whilst I know you do practice all sorts of glass techniques Pat, but I'd say it was more important to hoover out a fusing kiln than one used only for annealing. When annealing, a speck of brick dust/thinfire residue isn't going to harm a bead, because it's already set - but with fusing, or casting, or other work that reaches higher temperatures in the kiln, then dust dropping on your glass when it's going up to 800 degrees is something you REALLY don't want happening....
Quote from: Rikki on February 12, 2011, 08:38:06 PM
Vacuum my kiln?? I don't even vacuum my house if I can help it! After all, what are children for??!! ;D
He he he, I am of the same mind, however I do vacuum the inside of my kiln more then anything else ::)
----
My tutor at college also vacuums the inside of the big glass kilns in between every firing.
It's simply another question of whether you want to spend an extra couple of minutes to prevent any contamination during a firing. For me it falls into the same catagory as cleaning out my lost wax molds with boiling water, even after they've been steamed out, yes I could simply not bother, but the crucial firing I don't do that is the one that a tiny bit of wax remains and contaminated the entire cast.
I can't see any crud on here, can you (http://pic20.picturetrail.com/VOL1426/5604171/12685369/229614336.jpg) combed glass at 930-940 degrees centigrade, or (http://pic20.picturetrail.com/VOL1426/5604171/12685369/229614340.jpg)
I got a roll of a thicker paper from Creative Crafts at Rochester. Might be Bullseye.I thought it was pricey at the time but it has proved to be worth it
So does the thicker paper mean it can be fired more than once?
or do you layer?
or a much more sensible option would be u brush it off?
I really don't think that I could leave the dust as it is a top opening kiln, when I open is blows about a bit.
I use 3mm Fibre Paper in Big Blue, which I don't hoover untill I'm ready to remove it completely and re-line him, as it would destroy it to hoover it. The top loader and my bead-cube I hoover when needed, which can be after every firing or not, it's preety obvious when you need to do so and depending on what you are using!
However, I'm more than happy to do a personal inspection of people's kilns for a recommendation of hoovering requirements for my standard hourly rate plus travel expenses! ;)