Frit-Happens !

Lampwork => Common Problems => Topic started by: sarah t on December 04, 2010, 03:47:43 PM

Title: flame being 'pushed' away from torch ???
Post by: sarah t on December 04, 2010, 03:47:43 PM
just gone out to torch after all this rubbish weather and the flame appears to be being pushed away from the torch and there is a gap between torch and flame  ???..is this oxycon or propane ???.... oxgen comming through but oxycon seams a bit sluggish and gas could be low (sods law!) but they are not friends and wont play nice !!
Title: Re: flame being 'pushed' away from torch ???
Post by: Nick on December 04, 2010, 04:22:43 PM
Hi

Try turning the gas down slightly before lighting this should solve it.The cold will affect the gas.

Regards
Title: Re: flame being 'pushed' away from torch ???
Post by: Dragonfire Glass on December 04, 2010, 05:59:12 PM
just your oxycon taking a bit longer to get going. Give it a minute or two and it'll be fine
Title: Re: flame being 'pushed' away from torch ???
Post by: sarah t on December 04, 2010, 07:01:20 PM
i think it is oxycon too ...it started bleeping at me not long after posting question  :'(.....i will try it again tomorrow ...i kept him wrapped up and put the heater on each day to take the chill off but i really think he does not like this weather at all poor little chap  :)


i will check threads for a look and see if there is anything extra i can do to make him feel better ...i am hoping nothing inside has frozen  :( 
Title: Re: flame being 'pushed' away from torch ???
Post by: Redhotsal on December 04, 2010, 07:15:57 PM
The gap is because you've got air rather than oxygen coming through. I echo what the others are saying - this bad weather isn't doing oxycons any favours right now...
Title: Re: flame being 'pushed' away from torch ???
Post by: LampyLou on December 08, 2010, 09:23:19 AM
Thanks for posting this, I've been having the same trouble.  My kit is in the garage and on top of the funny flame it keeps going out.  I've figured out that it takes about 15-20 mins for the oxycon and gas to warm up properly and produce a nice flame.  As I'm always too impatient to wait I've found that this is a good time to practice my stringers and twisties.

Cos it's so cold I take a break after about 1-1.5 hours and I do find that when I come back I get a good flame almost straight away.

Julia
Title: Re: flame being 'pushed' away from torch ???
Post by: julieHB on December 08, 2010, 12:09:31 PM
I have had a lot of starting up problems with my oxycon, and i found that letting the oxycon run on low flow (2-2.5 l/min) for 15-30 mins before opening the propane and lighting the torch was the best way. Just remember to open the oxygen valve on the torch as well - it does not like working against a building pressure!!

When you want to light the torch just open the propane on the cylinder, turn the oxygen on the torch down, open the propane on the torch, light, and open the oxygen valve on the torch again.

I cannot remember where I read it, but it was strongly advised never to let the oxycon run for less than half an hour. Doing that can cause build-up of moisture in the sieve beds, which is very, very bad for the health of your oxycon. These machines are built for hours of continuous running, and not short periods of operation.
Title: Re: flame being 'pushed' away from torch ???
Post by: beadysam on December 08, 2010, 03:29:44 PM
I always used to get this problem when I first started, and also had to adjust the flame continually for the first half hour or so.  It was easily solved by turning on my oxycon on low (about 1ltr) for 10-15 mins while I got myself sorted out, tidied up a bit, turned on the gas bottle and picked out glass rods etc.  The oxycon seemed much happier this way and it meant I wasn't using it at max capacity before it had got its back up cylinders nice and full.  Hope that helps ;)
Title: Re: flame being 'pushed' away from torch ???
Post by: Lotti on December 08, 2010, 03:41:26 PM
When your kit is in a cold (potentially damp) outside building do folks wrap their oxycons up in a blanket!?  I see Sarah mentions wrapping hers up. :)
Title: Re: flame being 'pushed' away from torch ???
Post by: sarah t on December 08, 2010, 03:55:57 PM
i wrap mine up when it gets chilly in some bubble wrap and a blanket  ..after a sssion i turn off the oxycon and keep the torch valve open to let the pipes etc empty and then i wrap him up .....i am outside in a chilly. damp ,blinkin cold shed too ...

but this last week as it was too cold to torch and considering the problems 'henry' was having i bought him inside hoping that a holiday in warmer climes would make him happy again  ;)...been asked a couple of times who the darlik in the corner is  ;D
Title: Re: flame being 'pushed' away from torch ???
Post by: Lotti on December 08, 2010, 04:55:16 PM
Quote from: sarah t on December 08, 2010, 03:55:57 PM
i wrap mine up when it gets chilly in some bubble wrap and a blanket  ..after a sssion i turn off the oxycon and keep the torch valve open to let the pipes etc empty and then i wrap him up .....i am outside in a chilly. damp ,blinkin cold shed too ...

but this last week as it was too cold to torch and considering the problems 'henry' was having i bought him inside hoping that a holiday in warmer climes would make him happy again  ;)...been asked a couple of times who the darlik in the corner is  ;D

:D :D :D :D  Did it cheer him up? :)  My other half wanted to upwrap mine that came today and when he saw the size of it, we decided to leave it in its packaging until ready to go! :)  Like the idea of a name, will have to think of one! :)
Title: Re: flame being 'pushed' away from torch ???
Post by: Fruddy on December 08, 2010, 06:00:25 PM
Quote from: Lotti on December 08, 2010, 03:41:26 PM
When your kit is in a cold (potentially damp) outside building do folks wrap their oxycons up in a blanket!?  I see Sarah mentions wrapping hers up. :)

I wrap mine up in a massive piece of foam insulation - I also have a thermotube in the shed to keep the temperature a bit higher than it is outside.
Title: Re: flame being 'pushed' away from torch ???
Post by: sarah t on December 08, 2010, 11:08:34 PM
as the temperature has risen above freezing today i am hoping i will find out tomorrow if henry's holiday has worked ...they say a change is as good as a rest  ;)
Title: Re: flame being 'pushed' away from torch ???
Post by: AnnaSpanna on December 10, 2010, 11:43:43 AM
Quote from: sarah t on December 04, 2010, 07:01:20 PM
...i kept him wrapped up and put the heater on each day to take the chill off but i really think he does not like this weather at all poor little chap  :)


This paints such a sad and sorrowful picture.... a poor shivering shaking oxycon with a little icicle hanging of its power button wearing a little red and yellow striped hat and scarf (dunno why but that is what he's wearing in my head)... and he is inevitably wondering "why does nobody love me? is there an oxycon home I can go to for unloved oxycon and other rennovated ex-medical equipment? or perhaps even an oxycon soup kitchen as I will inevitably be left switched on and outside in the shedio over christmas.... Wwwwaaaaaaaaaaarrrrgggghhhhhh! *sobs*"

Oh poor wee oxycon.... but hey he might just have manflu!!!!!!!!!

oh my poor head - too many meds methinks!
Title: Re: flame being 'pushed' away from torch ???
Post by: awrylemming on December 10, 2010, 01:17:11 PM
Quote from: AnnaSpanna on December 10, 2010, 11:43:43 AM
Quote from: sarah t on December 04, 2010, 07:01:20 PM
...i kept him wrapped up and put the heater on each day to take the chill off but i really think he does not like this weather at all poor little chap  :)


This paints such a sad and sorrowful picture.... a poor shivering shaking oxycon with a little icicle hanging of its power button wearing a little red and yellow striped hat and scarf (dunno why but that is what he's wearing in my head)... and he is inevitably wondering "why does nobody love me? is there an oxycon home I can go to for unloved oxycon and other rennovated ex-medical equipment? or perhaps even an oxycon soup kitchen as I will inevitably be left switched on and outside in the shedio over christmas.... Wwwwaaaaaaaaaaarrrrgggghhhhhh! *sobs*"

Oh poor wee oxycon.... but hey he might just have manflu!!!!!!!!!

oh my poor head - too many meds methinks!


Beautifully written, I can hear the violins  :'(  ;D
Title: Re: flame being 'pushed' away from torch ???
Post by: sarah t on December 10, 2010, 01:32:48 PM
well the '' poor little chap'' is going to get a kick up his filter !!...he will still not play nice ....not sure if while on his holidays someone fiddled with his buttons or he is just on strike ...he has more lights flashing on him than a blinkin christmas tree .....i have checked through old threads and i think he may have damp in his filter bed ???......arrrrgggggg
Title: Re: flame being 'pushed' away from torch ???
Post by: AnnaSpanna on December 11, 2010, 11:51:46 AM
nowt worse than a damp filter bed....... ???