Frit-Happens !

Technical Forum => Studio/workspace/setup/equipment => Oxycon/Oxygen/Propane => Topic started by: Kalorlo on November 19, 2010, 04:26:21 PM

Title: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 19, 2010, 04:26:21 PM
I need to add quick releases to my current propane hose so I can finally get my Minor up and running. Problem is, I have 6mm ID hose (bulk kit from Martin), and all the quick releases I can find *anywhere* are for 8mm ID hose.

I know some of you have done this yourselves before! Did you have 6mm hose and the 8mm ones fit anyway? Or do I need to replace the whole hose and fittings? I'm very confused - I know that Martin sells quick releases, but his don't specify what size they actually are and are extremely expensive. The whole hose route would be much cheaper, especially as I need two (or one and a half, but eh).

I did have a search around, and supposedly 6mm ID hose is the ideal size for a Minor, so that's not so bad... if I can find the pieces to fit!

???
Title: Re: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 20, 2010, 07:26:00 PM
Anyone got a clue? I don't want to end up in a situation where I've taken my Hot Head off and end up with no connected torch!
Title: Re: Quick releases - question for people who sourced their own
Post by: Lush! on November 20, 2010, 07:46:11 PM
Nope, can't help sorry.  I'm so clueless about stuff like this, I actually got Martin to connect quick releases on all my torches so I can just swap and change whenever I want to.
Title: Re: Quick releases - question for people who sourced their own
Post by: ♥♥Tan♥♥ on November 20, 2010, 08:49:27 PM
George is really good on things like this I think
Title: Re: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 20, 2010, 08:59:18 PM
I asked her first  ;)

It's the size thing that's the problem - George said she'd used 8mm all the way through for her setup. Which I can do if I just start again. But if 6mm quick releases don't actually exist and I can use 8mm anyway, then that's easier!

I mean, I can ask Martin what size his quick releases actually are, but that's rather cheeky if I'm going to turn round and get them somewhere else...
Title: Re: Quick releases - question for people who sourced their own
Post by: ♥♥Tan♥♥ on November 20, 2010, 09:04:35 PM
Have you asked at your local plumbery type place? I find if I simper and tell them how manly they are those hairy apes love helping out ;)
Title: Re: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 20, 2010, 09:09:15 PM
Meh, I was hoping not to have to speak to them until I actually knew the answer! We'll see, but I'm kinda expecting them to go, "No, that says 6mm, it won't fit". Or just stare at me blankly.
Title: Re: Quick releases - question for people who sourced their own
Post by: awrylemming on November 20, 2010, 10:38:44 PM
I'm going to buy some from Martin on Monday, just bought my set up and thought they came with, and now realise they dont so really need to get them. I'll ask for you if you like?
Title: Re: Quick releases - question for people who sourced their own
Post by: dangerousbead on November 20, 2010, 10:40:06 PM
I went through all this recently when the coupler failed on my bulk to hh. It got so complicated that I decided Martin was the best bet, expensive or not. He usually is. Bless him. :-)
Title: Re: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 20, 2010, 10:43:49 PM
Quote from: awrylemming on November 20, 2010, 10:38:44 PM
I'm going to buy some from Martin on Monday, just bought my set up and thought they came with, and now realise they dont so really need to get them. I'll ask for you if you like?

That would be really sweet of you! I'll also try the gas/hardware place along the road that's open on Sundays and see if they know anything.
Title: Re: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 21, 2010, 02:34:17 PM
Well, that was a waste of time! The place that the Calor website says is a Calor shop is actually a grocery shop...
Title: Re: Quick releases - question for people who sourced their own
Post by: ♥♥Tan♥♥ on November 21, 2010, 02:47:48 PM
I shouldn't laugh.........
Title: Re: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 21, 2010, 02:50:14 PM
 :P  ;D

At least I took the recycling out?
Title: Re: Quick releases - question for people who sourced their own
Post by: ♥♥Tan♥♥ on November 21, 2010, 02:54:11 PM
Somedays its laugh or scream isn't it :D
Title: Re: Quick releases - question for people who sourced their own
Post by: garishglobes on November 21, 2010, 11:08:03 PM
If you want gas, eat sprouts.
Title: Re: Quick releases - question for people who sourced their own
Post by: garishglobes on November 21, 2010, 11:14:38 PM
Does this help? These guys seem to have an awful lot of them...

http://www.cwberry.com/ProductCat.aspx?TreeNodeId=158C2685-F44E-494F-A1CF-0211AF06A4BA&Ite
msPerPage=300 (http://www.cwberry.com/ProductCat.aspx?TreeNodeId=158C2685-F44E-494F-A1CF-0211AF06A4BA&Ite%3Cbr%20/%3EmsPerPage=300)
Title: Re: Quick releases - question for people who sourced their own
Post by: Kalorlo on November 23, 2010, 01:58:02 PM
Aha, I found something! From Sundance Glass:

"You can get the smaller 1/4" hose listed above on these large inlet fittings with a bit of effort. A trick is to immerse the end of the hose in very hot water to soften the end."

They're talking about fittings that they otherwise sell 3/8" hose for. Ok, I'm a lot happier now. I did email another gas place to ask, but if they don't say anything, I think I'll go ahead and get 8mm ones. After I've made things for Christmas, though!

From the piccies it looks like the ones Martin has might be imported Western Enterprises QDB20 releases. Maybe. Which are 1/4" and would explain the price. Or wait, maybe not QDB20, since those still have B fittings?