Frit-Happens !

Technical Forum => Studio/workspace/setup/equipment => Tools and Presses => Topic started by: SallyB on January 13, 2010, 11:00:12 PM

Title: Is my Tungston Rake really Tungston?
Post by: SallyB on January 13, 2010, 11:00:12 PM
Hello

I wonder if someone might be able to help me.

I liked my stainless steel rake but the sticking annoyed me so I bought a Tungston one from Off Mandrel a while ago.  It sticks and I didn't think it would which makes me wonder if I'm doing something wrong or there's been a mistake (as seems to happen a lot to me with glass suppliers) and it's really stainless steel.

I'm mainly using it for pushing hot glass around to create beads like this:
(http://i229.photobucket.com/albums/ee34/SallyB_photo/mybeads7.jpg)

Is there some way to tell if it's really Tungston?

Thank you for any help you may be able to give me.

Sally
Title: Re: Is my Tungston Rake really Tungston?
Post by: Carl Martin on January 13, 2010, 11:44:02 PM
Stainless Steel will bend keep bending it and bending it and it will snap ~ metal fatigue.

Tungsten doesn't bend ~ if you try and it is tungsten, it will snap. It will take a bit of force but Tungsten has no memory and although super tough it is brittle.

Hope that helps.
Title: Re: Is my Tungston Rake really Tungston?
Post by: Sam on January 13, 2010, 11:48:19 PM
Your pick might be sticking to the glass because it's hot.

Each time you use your pick on a hot bead you should cool it by plunging it in a small bowl
of water before touching the bead with it again.

As for knowing whether your pick is tungsten, can't help there I'm afraid ???

Hope this helps

Sam ;D
Title: Re: Is my Tungston Rake really Tungston?
Post by: Redhotsal on January 13, 2010, 11:57:21 PM
If you put your tungsten pick really low in a very hot flame you will be able to get it to fume. Tungsten fumes are bright yellow. I dont' think I've seen steel act in the same way. Don't breathe in the fumes and make sure you have good extraction.
You can also try this- heat up the pick until glowing and then use the glowing pick to try and make a hole in the glass - if it's tungsten it will do this pretty easily. If it's steel you'll have great fun trying to extricate your pick from a molten glob of glass. Dunking the tool in water will clean off the hot glass.
You can rake your beads with any old steel tool - doesn't have to be tungsten. However, you need to avoid using the tool in direct flame - that's just a bad practice and will ruin your tools over time. Best way is to heat the bead up to glowing orange and then rake it, but out of the flame.
Title: Re: Is my Tungston Rake really Tungston?
Post by: Ian Pearson on January 14, 2010, 07:40:28 AM
Sal is right about the yellow fumes off from Tungsten. Tungsten will stick to glass as will most metals I know. Under good working conditions boro can make an excellent seal and sometimes one can make a handle from glass bonded to tungsten rod to aid working although pin vices probably are better for some.

Ian
Title: Re: Is my Tungston Rake really Tungston?
Post by: SallyB on January 14, 2010, 06:35:23 PM
Thank you very much for the advice
I'm not going to have a go at bending it.
I guess it probably is Tungston and I'm probably doing something wrong which is good because I can learn and fix my mistakes.
Thanks Sal, I'll try that fuming trick next time I'm out in the shed - hopefully it's tungston and I can correct my technique mistakes.

I really appreciate the help
thank you very much

Sally
Title: Re: Is my Tungston Rake really Tungston?
Post by: Hamilton Taylor on January 15, 2010, 08:48:28 AM
If you have any doubts, please feel free to return it and we'll replace it free of charge.

Sean