Frit-Happens !

Technical Forum => Studio/workspace/setup/equipment => Torches => Topic started by: BeadyBugs on April 01, 2007, 07:07:01 PM

Title: How to connect a Hothead to a Creation Station.
Post by: BeadyBugs on April 01, 2007, 07:07:01 PM
Evening!

I've been asked if I'd got any photos of how to attach a Hothead torch to a Creation Station, so here you go.  Some of these methods work just as well without the CS, and would be fine ways to attach the HH straight on to a table.

1.  HotHead with MAPP cannister and various DIY bits and bobs. (G-clamp, large jubilee/hose clip, corner brace)

(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappSetupClips1.jpg)
(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappClipsCloseup.jpg)


2.  Hothead with bulk propane set up.  (Same set up as above, just with a smaller jubilee clip around the torch)

(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSBulkPropSetup1.jpg)


3.  Hothead with MAPP canister using CS bracket, this would work on bulk too (not sure how secure this one is though?)

(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappBracket.jpg)
(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappBracketCloseup.jpg)

Have fun, and play safe kids! ;D

HP x
Title: Re: How to connect a Hothead to a Creation Station.
Post by: Trudi on April 01, 2007, 08:05:20 PM
Thank you so much for that!!

Trudi
Title: Re: How to connect a Hothead to a Creation Station.
Post by: Trudi on April 02, 2007, 01:35:33 PM
Hi Helen

I'm using a HH on bulk - but my torch is almost pointing straight up - yours looks more angled - is that right? I'm trying to see how you've clamped yours on!

T
Title: Re: How to connect a Hothead to a Creation Station.
Post by: BeadyBugs on April 02, 2007, 02:36:59 PM
Hi Trudi,

Using the bracket that comes with the CS, the torch does end up pointing really upwards.  I never actually used this method as I prefer the torch to be at more of a 45 degree angle to the table.  Also - the torch never felt that secure just being held in position by a couple of bits of rubber.  So I always used the small jubilee clip arrangement in the second set up, and you can bend the corner brace to whatever angle you like.

Hope that helps. ;)

HP x
Title: Re: How to connect a Hothead to a Creation Station.
Post by: Caroline on April 02, 2007, 04:31:56 PM
Quote from: shine-on2 on April 02, 2007, 01:35:33 PM
Hi Helen

I'm using a HH on bulk - but my torch is almost pointing straight up - yours looks more angled - is that right? I'm trying to see how you've clamped yours on!

T

i used mine like that!! i now have my minor set up the same
Title: Re: How to connect a Hothead to a Creation Station.
Post by: amber0307 on February 18, 2008, 10:01:01 PM
Sorry if I'm being a bit of a ditz, but could someone spell out for me exactly what I need to fit my torch to my bench.  Planning on investing in a creation station and using a hothead torch with Mapp canister.  Just need to know exactly what I need, and where to get it from!  A bit confused.

Thanks :)
Title: Re: How to connect a Hothead to a Creation Station.
Post by: *rowanberry* on February 18, 2008, 10:03:42 PM
If you got a creation station, then nothing at all, its fully equiped to hold your hothead and can - you just set it up like bottom picture below, the bracket etc is on the creation station.

I hope that helps!
Title: Re: How to connect a Hothead to a Creation Station.
Post by: amber0307 on February 26, 2008, 02:00:03 PM
Quote from: *rowanberry* on February 18, 2008, 10:03:42 PM
If you got a creation station, then nothing at all, its fully equiped to hold your hothead and can - you just set it up like bottom picture below, the bracket etc is on the creation station.

I hope that helps!

I've not bought a creation station yet (my poor wallet!) but ordered bench clamps along with my starter kit from Tuffnell.  Is there anything else I need (can I buy hose and clips etc from B & Q?)

Also is it better to screw torch directly onto my worksurface or as some of you have done use some board or metal to screw it onto?
Title: Re: How to connect a Hothead to a Creation Station.
Post by: amber0307 on March 15, 2008, 04:07:54 PM
Quote from: Helen P on April 01, 2007, 07:07:01 PM
Evening!

I've been asked if I'd got any photos of how to attach a Hothead torch to a Creation Station, so here you go.  Some of these methods work just as well without the CS, and would be fine ways to attach the HH straight on to a table.

1.  HotHead with MAPP cannister and various DIY bits and bobs. (G-clamp, large jubilee/hose clip, corner brace)

(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappSetupClips1.jpg)
(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappClipsCloseup.jpg)


2.  Hothead with bulk propane set up.  (Same set up as above, just with a smaller jubilee clip around the torch)

(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSBulkPropSetup1.jpg)


3.  Hothead with MAPP canister using CS bracket, this would work on bulk too (not sure how secure this one is though?)

(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappBracket.jpg)
(http://i154.photobucket.com/albums/s250/BeadyBugs/Hothead%20Setup/CSMappBracketCloseup.jpg)

Have fun, and play safe kids! ;D

HP x




I know that when attaching hothead to a creation station using the cs bracket it ends up pointing straight upwards, but in the first pic you have it attached to a strip of bent metal with holes in........does this have a specific name or is it just something you made yourself?  I'd like the same setup! :)