Frit-Happens !

Lampwork => Common Problems => Topic started by: beading bloke on November 24, 2009, 07:06:06 PM

Title: bead release
Post by: beading bloke on November 24, 2009, 07:06:06 PM
Hi all.
        My bottle of bead release has gone a bit thick and lumpy despite giving it a good shake before using it.can i just add water to it to make it OK again.May thanks.
Title: Re: bead release
Post by: Tollgate-Debs on November 24, 2009, 07:12:41 PM
I add water when needed - a little at a time and mix it well.  I also add a few beads into each pot which helps to agitate the mixture when shaken.

Debs
Title: Re: bead release
Post by: Lush! on November 24, 2009, 07:29:41 PM
Just make very very very sure you've put the lid on properly before you shake!  ;)
Title: Re: bead release
Post by: GoodMonkey on November 24, 2009, 08:06:10 PM
Quote from: Lush! on November 24, 2009, 07:29:41 PM
Just make very very very sure you've put the lid on properly before you shake!  ;)

There speaks the voice of experience.......
Title: Re: bead release
Post by: julieHB on November 24, 2009, 08:11:53 PM
Quote from: GoodMonkey on November 24, 2009, 08:06:10 PM
Quote from: Lush! on November 24, 2009, 07:29:41 PM
Just make very very very sure you've put the lid on properly before you shake!  ;)

There speaks the voice of experience.......

...erm...I don't shake the bottle any more - I use a thick mandrel and stir it before use....I never, never, ever want to clean up splattered bead release from all over my glass, floor, workbench ever again!!!  ::)
Title: Re: bead release
Post by: Margram on November 24, 2009, 08:19:20 PM
I've written a warning on my lid - it's only a matter of time before I get so used
to seeing that that I just don't see it... ::)

Someone (was it Trudi?) said to use distilled water to dilute it.
Title: Re: bead release
Post by: Steampunkglass on November 24, 2009, 08:55:10 PM
Someone posted it's better to use distilled water; I've only been using tap water and the mix isn't as good as when I bought it so may well help prolong the life of it.
Title: Re: bead release
Post by: fionaess on November 26, 2009, 10:47:30 PM
I've always used tap water with my Foster Fire - and its fine...just as good as the first time :)
Title: Re: bead release
Post by: sublimekate on November 26, 2009, 10:52:19 PM
Yep I just put some tap water in, and if it's too runny leave the lid off for a bit  ;D

Shaking it with the lid off!! Oh dear, messy  ;D
Title: Re: bead release
Post by: Les on November 26, 2009, 10:57:02 PM
Quote from: Lush! on November 24, 2009, 07:29:41 PM
Just make very very very sure you've put the lid on properly before you shake!  ;)

Damn right ! ;)
Title: Re: bead release
Post by: Betty the Chook on November 26, 2009, 11:12:27 PM
I use a little whisk to give it a good mix up. Just don't leave the whisk in as it goes rusty very quickly - not nice.... but better than bead release splattered everywhere!
Title: Re: bead release
Post by: glassworks on November 27, 2009, 09:46:52 AM
the only thing to be aware of is NOT TO USE SOFTENED WATER!!!!.... apparently the salts cause the fosterfire to breakdown and crumble when dry?.. i asked robin about this and she confirmed it is best to use distilled or plain tap water only!...

and, tighten the lid... i've done it too.... i also chuck a few fuggly beads into the bottle to act as a "stirrer" to get the lumps off the bottom.. makes a neat rattle too!...
Title: Re: bead release
Post by: princess pink on November 27, 2009, 11:04:07 AM
i've been using bottled mineral water as i didnt have any distilled...do you think thats ok?
Title: Re: bead release
Post by: turnedlight on November 27, 2009, 02:28:01 PM
I've been using rainwater - just leave my jars outside the shed - I wonder if that's bad? ??? :)
Title: Re: bead release
Post by: glassworks on November 27, 2009, 02:49:31 PM
rain water is fine... i would think that bottled (flat) water is fine too, as it is mostly just filtered tap water anyway!..  ;D :D ;D

seriously though, from what robin explained it was the additional salts that the water softener added that caused the issues...

anyone else had any experience of the flaky bead release - i know we replaced a few bottles before robin cottoned on to what the issue was...
Title: Re: bead release
Post by: Margriet on November 27, 2009, 08:46:29 PM
I use this one:
(http://www.baby-walz.com/bilderneu/743/sortiment/wh270q80/287130.jpg)

My husband ordered it here. (http://www.baby-walz.com/SyEngine.php?Act=97694&Do=97702&pId=512987&pNummer=287130&pWerbetraeger=743)
The kids thought I was pregnant  ;)

In the Netherlands we tested 14 beadreleases:

(http://www.margrieten.nl/wp-content/uploads/DebeadreleasetestvanHetGroteGlasForum_1017A/Beadreleastest.jpg)
Click here for the report. (http://www.margrieten.nl/Beadreleasetestrapport20090913.pdf)