Frit-Happens !

Technical Forum => Studio/workspace/setup/equipment => Tools and Presses => Topic started by: Lush! on May 14, 2009, 09:40:14 AM

Title: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 09:40:14 AM
I've just been browsing some Murano videos on You Tube and had one of those classic forehead-slapping-penny-dropping moments!

I've never really got the point of rod warmers, but when I noticed the little nudge this lady gives the clear rod at about 1.02 min I suddenly realised she's using the warmer to keep the tip of the clear right in the flame and have a big gather ready to encase her bead with no fussing about at all!

http://www.youtube.com/watch?v=EMn9H0b85To (http://www.youtube.com/watch?v=EMn9H0b85To)


Wow!

Er ... am I the last to realise this?  Are you all rolling your eyes at me now?  ::)

;D

edited to add link, doh again!
Title: Re: Rod Warmers? Doh!
Post by: sarah t on May 14, 2009, 09:46:30 AM
i did not even know there was such a thing as a rod warmer ......i never got the thing about torch top marvers till i realised you could use then to warm up your bits  ;)
Title: Re: Rod Warmers? Doh!
Post by: sublimekate on May 14, 2009, 09:46:52 AM
Not just you Julie..

Doh!! here too  ;D
Title: Re: Rod Warmers? Doh!
Post by: Redhotsal on May 14, 2009, 09:50:53 AM
 ::)

hehe!  ;)

They're great - but they cost an arm and a leg. Yes, yes, I know you can make them yourself but I'm not making so many of my own tools now after my homemade hotfingers nearly hospitalised a student!
Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 09:52:06 AM
Glad to know me and my ignorance are in good company  ;D

Sal  :o  Now you've got to tell us more!
Title: Re: Rod Warmers? Doh!
Post by: Redhotsal on May 14, 2009, 09:57:47 AM
Hotfingers need FOUR prongs and not three otherwise your really hot marble will slip out between the gap, roll across the table - giving you a moment to recognise that all that work making it completely round has paid off - it will then fall off the table and land millimeters away from your student's right thigh, proceeding to melt noisily, with loads of smoke, down through the cushion your student is sitting on. Shudder........ :o :o :o
Title: Re: Rod Warmers? Doh!
Post by: SMHBuss on May 14, 2009, 10:12:01 AM
Sal...at least you didnt grab it!

Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 10:18:58 AM
Quote from: Redhotsal on May 14, 2009, 09:57:47 AM
Hotfingers need FOUR prongs and not three otherwise your really hot marble will slip out between the gap, roll across the table - giving you a moment to recognise that all that work making it completely round has paid off - it will then fall off the table and land millimeters away from your student's right thigh, proceeding to melt noisily, with loads of smoke, down through the cushion your student is sitting on. Shudder........ :o :o :o

that'll teach ya for showing off  :D
Title: Re: Rod Warmers? Doh!
Post by: Josephine on May 14, 2009, 10:23:43 AM
Whoops!
Title: Re: Rod Warmers? Doh!
Post by: Carol on May 14, 2009, 10:46:25 AM
Yay for four-pronged hotfingers!!  ;) :D
Title: Re: Rod Warmers? Doh!
Post by: Steampunkglass on May 14, 2009, 11:44:59 AM
QuoteHotfingers need FOUR prongs and not three otherwise your really hot marble will slip out between the gap, roll across the table - giving you a moment to recognise that all that work making it completely round has paid off - it will then fall off the table
Ah! I know that feeling so well! I am embarking on a new style of floor decoration called 'random charred stripes!'

As for the rod warmer, Martin has a frit tray on sale at moment that you can pop a nightlight underneath to keep the metal hot, not sure if it's any good or as hot as you'd need, but might be worth considering (it's in his clearance sale)
Title: Re: Rod Warmers? Doh!
Post by: Redhotsal on May 14, 2009, 11:47:30 AM
Quote from: strawackie on May 14, 2009, 10:46:25 AM
Yay for four-pronged hotfingers!!  ;) :D

Yay for the student who has survived the Redhotsal experience!!!!!!  ;)
Title: Re: Rod Warmers? Doh!
Post by: Trudi on May 14, 2009, 11:53:11 AM
I haven't tried, but could you leave the rod resting just inside the kiln - I have an SC2 with a bead door - not sure how easy this would be for others?
Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 11:53:27 AM
Quote from: Dendrobium on May 14, 2009, 11:44:59 AM

As for the rod warmer, Martin has a frit tray on sale at moment that you can pop a nightlight underneath to keep the metal hot, not sure if it's any good or as hot as you'd need, but might be worth considering (it's in his clearance sale)

Hmm, no actually, this is the point - I thought rod warmers were for keeping your whole rod warm, but in the video she uses it to hold the tip of the rod in the flame and actually melt the point of the rod so the gather is ready and waiting for the bead!  
Title: Re: Rod Warmers? Doh!
Post by: Steampunkglass on May 14, 2009, 11:57:15 AM
AH! Sorry, see what you mean now, I'm being dense again!  :-[ In that case I am sure it couldn't bee too hard to rig something up to hold it???
Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 12:24:35 PM
I'm sorry, I'm such a dope sometimes - I forgot to add the link in my first post, how on earth were you meant to know what I was going on about?!!  ???

Added now!
Title: Re: Rod Warmers? Doh!
Post by: Redhotsal on May 14, 2009, 12:31:15 PM
Quote from: Dendrobium on May 14, 2009, 11:57:15 AM
In that case I am sure it couldn't bee too hard to rig something up to hold it???

Ooooo - such dangerous thoughts!!!  ;D ;) I've decided that when I catch myself saying "well, how hard can it be to make......." something, I try and distract myself and think of something else!  :D
Title: Re: Rod Warmers? Doh!
Post by: Les on May 14, 2009, 12:32:43 PM
Oh now that's clever !
Title: Re: Rod Warmers? Doh!
Post by: Steampunkglass on May 14, 2009, 12:37:39 PM
ooo! I see why you're so excited, looks like it works even better than I'd imagined - plenty of times I've felt like I need an extra hand to hold something in the flame!

QuoteOoooo - such dangerous thoughts!!!    I've decided that when I catch myself saying "well, how hard can it be to make......." something, I try and distract myself and think of something else! 
Distractions not working, I'm now thinking of what lumps of tin and gaffa tape I have in the shed....... Someone stop me!
Title: Re: Rod Warmers? Doh!
Post by: Sulis (Hazel) on May 14, 2009, 12:48:16 PM
Quote from: Redhotsal on May 14, 2009, 11:47:30 AM
Quote from: strawackie on May 14, 2009, 10:46:25 AM
Yay for four-pronged hotfingers!!  ;) :D

Yay for the student who has survived the Redhotsal experience!!!!!!  ;)

The clue is in the title - you're not Redhot for nothing Sal! Sounds quite exciting though, I reckon you could market your tuition as one of those high adrenaline 'experiences'  ;D
Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 12:49:55 PM
White Knuckle Beads  ;D

Glenn, I've just tried the very technical "balancing rod on top of jam jar" technique, but I need a taller jar, so I might have to try "balancing rod on top of jam jar on top of bovril jar" next ... hey, I was trained by Redhotsal you know  ;)
Title: Re: Rod Warmers? Doh!
Post by: Redhotsal on May 14, 2009, 12:56:42 PM
Extreme Lampworking.
Heavens - what have I created??!

Still - looking at the Youttube video it does beg the question - could any of us made a bead that size in less than three minutes? Not sure that I could! (Too busy chasing hot things around and building useless glass tools!)
Title: Re: Rod Warmers? Doh!
Post by: Steampunkglass on May 14, 2009, 01:11:08 PM
Nah, takes me three minutes to decide what colour to use, then another three to remember what I am doing!
I think you can improve on the jam jar technique by adding some blobs of blue tack to make a little channel to stop the rods rolling off, and height can be adjusted by standing jam jar on books of varying thickness  ;)  :D I learnt so much about engineering from watching Tom & Jerry and Wille Coyote!!!  :P
Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 01:13:41 PM
Blue Tack, yay!

Oooh ooh, how about Museum Gel?  I've got a couple of pots somewhere ...  :D
Title: Re: Rod Warmers? Doh!
Post by: Steampunkglass on May 14, 2009, 01:15:59 PM
Quotehow about Museum Gel
That's all too new fangled for me! I'm all old technology here!
Title: Re: Rod Warmers? Doh!
Post by: Vicki on May 14, 2009, 01:59:47 PM
nope, I'd never heard of it either, I (like trudi) have been known to rest the odd rod of shocky glass into the kiln, but i have asbestos hands & it does get quite hot in there  ::)
Title: Re: Rod Warmers? Doh!
Post by: Redhotsal on May 14, 2009, 02:18:06 PM
Quote from: Dendrobium on May 14, 2009, 01:15:59 PM
Quotehow about Museum Gel
That's all too new fangled for me! I'm all old technology here!

I should hope so - or you wouldn't be Steam Punk!  ;D
Have you seen that valves are once again the latest thing in audio equipment now? We'll be cranking up cars from the front to start them next!
Title: Re: Rod Warmers? Doh!
Post by: Steampunkglass on May 14, 2009, 03:09:54 PM
QuoteWe'll be cranking up cars from the front to start them next!
LOL! I think where I live sounds like some people already do that on cold mornings!
Yes heard about, the valve thing in audio amps, (very good technical reasons for this & why semiconducters can't hack it, but I shalln't bore you with it all!) it just goes to show that every thing has a place, however old fashioned it might seem; and there is nothing quite like curling up in front of a hifi with a nice warm valve glow (although that might just be me!)
Title: Re: Rod Warmers? Doh!
Post by: catriona on May 14, 2009, 04:08:40 PM
Wow i like the look of that i, going to let my hubby and bro see this and see if the can come up with something simler .
xxcatxx
Title: Re: Rod Warmers? Doh!
Post by: Dragonfire Glass on May 14, 2009, 05:03:59 PM
I was wondering if the filming was speeded up!

How about a metal try on top of the kiln, or someone uses those tea light thingies you see in Chinese restaurants, or didn't I hear of the hot plate from a slow cooker?
Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 14, 2009, 05:11:50 PM
Do you all see what she does just over a minute in?  The clear rod is on the warmer, but its tip is in the flame and at 1.02 she nudges it a little more into the flame so the end is almost melted enough to completely encase the bead.  I don't think a kiln or hot plate is going to warm it enough to do what she does.



Title: Re: Rod Warmers? Doh!
Post by: sarah t on May 14, 2009, 05:19:29 PM
it should not be too difficult to make something ...its if it would get hot and finding a material which is heat resistant ...the first thing that came to mind was  thin corrugated iorn on some kind of ajustable slope .......those frit trays might work ?
Title: Re: Rod Warmers? Doh!
Post by: Redhotsal on May 14, 2009, 05:32:43 PM
You can get the rod warmers in the UK but they're pricely - the main reason is because they have a very heavy base and are pretty solidly built. You wouldn't want a fully loaded rod warmer with loads of hot glass rods just toppling over.
Title: Re: Rod Warmers? Doh!
Post by: Dragonfire Glass on May 14, 2009, 06:09:37 PM
I'd have to relearn how to make beads too - cos it would get in my way!  :D
Title: Re: Rod Warmers? Doh!
Post by: Kaz on May 14, 2009, 06:41:23 PM
This is all starting to sound a bit too Heath Robinson for me - easier to have another arm grafted on I would imagine ;D
Title: Re: Rod Warmers? Doh!
Post by: Ilona on May 14, 2009, 07:08:38 PM
How about this?

I found this the other night, and might order one when I get back from my hols.

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MEWAX:IT&item=390050105237
Title: Re: Rod Warmers? Doh!
Post by: Pat from Canvey on May 15, 2009, 08:37:32 AM
If you want something to just warm up the glass rods, then an old George Foreman grill cleaned up works perfectly. I bought one in a boot sale for £2.50. The grooves are just the right size for rods.
Title: Re: Rod Warmers? Doh!
Post by: Trudi on May 15, 2009, 09:35:46 AM
Quote from: Kaz on May 14, 2009, 06:41:23 PM
This is all starting to sound a bit too Heath Robinson for me - easier to have another arm grafted on I would imagine ;D
LOL  ;D
Title: Re: Rod Warmers? Doh!
Post by: Lloki on May 15, 2009, 10:48:45 AM
Blimey, it's such a simple idea - it's brilliant!
Only problem was, I watched the YouTube video, then had to watch another one, then, I'll just watch that one, then, oh - that one looks interesting.
Next thing I know, a whole hour's gone by and no ironing has been done - SHAME! ;D
Right, off to find some jam and marmite pots!!!
Title: Re: Rod Warmers? Doh!
Post by: Lush! on May 15, 2009, 10:51:09 AM
Don't forget to look for another arm and a skin-grafting kit  ;)

Or you could just buy the one that Ilona found !!